Factory Seconds
Item: EX10020067
|Model: S-PLASMA 125H
Plasma Cutter - 125 A - 400 V - pilot arc
€839.00
Qty
Discount
Per item
3+
5%
€797.05
5+
10%
€755.10
10+
15%
€713.15
Key features
- Effective—cutting depth up to 34 mm
- Outstanding performance—125 A cutting current at a duty cycle of 60%
- Flexible—maximum freedom of movement thanks to the 5 m long plasma hose and the 3 m long ground cable
- Sophisticated—range of functions such as pilot ignition, operating modes for short-term and continuous operation, follow-up cooling, overheating protection
- Easy-to-read—LED display for monitoring performance
Accessories
Delivery details
Returns and warranty
Downloads
STAMOS 125A plasma cutter
Professionally made plasma cutter with a large power reserve. 3 x 400V power supply is a big advantage for those who have three-phase power supply available in their workshops. When plasma cutting thicker elements, the power load is distributed over three phases and we do not overload the electrical installation as it happens with devices powered from one phase 230V. I recommend the device for equipping a workshop as a stationary one. You can power a CNC plotter from this device and it will work well, because the parameters of the device allow for long continuous operation at a current of up to 80A. All spare and consumable elements are available - standard and not expensive. For this price, the device exceeded my expectations.
Technical details
Frequency [Hz]
50
Ignition Plasma
Pilot ARC
Voltage [V]
400
IP protection class
IP21S
Constant pressure [bar]
7
Air flow [l/min]
250
Duty cycle for 40°C [%]
60
Output current [A]
10 - 125
Input power [kVA]
15.4
Power factor
0.93
Cutting width [mm]
1.4
Gas after-flow [s]
5, 10, 60
Max. input power [kVA]
21.8
Insulation class
F
Max. input current [A]
31
Rated Input current [A]
22
CNC
No
2T / 4T
Yes
Water cooling
No
Gas test function
Yes
Power cord
3.8 m
Plasma cable
5 m
Air pressure
7 Bar
Ground cable
3 m
Max cutting thickness
34 mm
Air pressure hose length [m]
4
Dimensions (LxWxH)
63.5 x 27 x 40 cm
Weight
27.8 kg
Shipping dimensions (LxWxH)
74 x 37 x 50 cm
Shipping weight
32.8 kg
Delivery package
- Plasma cutter S-PLASMA 125H
- Plasma cable assembly: 5 m
- Air hose: 4 m
- Grounding cable: 3 m
- Ceramic nozzle
- 5 cutting nozzles
- 5 plasma electrodes
- Pressure gauge and pressure regulator
- 2 clamp rings
- Wrench
- Hose cover
- Delivery WITHOUT mains plug.
Product Description
Plasma Cutter - 125 A - 400 V - pilot arc
The plasma cutter S-Plasma 125H from Stamos Selection has plenty of power reserves for cutting through thick metallic materials using air plasma. Performance and handling are designed for high work efficiency, as required in professional metalworking. The plasma cutter is equally at home in automotive workshops and in metalworking businesses and industrial production. But even do-it-yourselfers with demanding projects appreciate the cutting power of the S-Plasma 125H.
The plasma cutter from Stamos Selection is designed for a professional work environment in which work progress and high-quality results count. It operates with a 400 V three-phase operating voltage and cuts workpieces from a wide variety of metallic materials. These include low and high-alloy tool steels as well as the non-ferrous metals aluminium, copper and titanium.
With a cutting depth of 34 mm, the plasma cutter is equipped for demanding repair and renovation tasks as well as for efficient use in production. Material loss is kept to a minimum with a cutting width of only 1.4 mm. The high performance is made possible by the particularly reliable IGBT inverter technology.
At a duty cycle of 60 percent, the cutting current is 125 A. At 100 percent duty cycle, a high 96.8 A is still possible. With an operating range between 10 and 125 A, the Stamos provides the necessary flexibility in the selection of the cutting current. The pilot ignition works contact-free and extremely reliable. The compressed air for plasma cutting is adjusted via a pressure reducer. The external compressor can be selected according to requirements and conditions. This makes the unit very flexible and easy to transport.
However, high equipment performance alone is by no means sufficient for efficient work. With its 5 m long plasma hose in connection with the 3 m long ground cable, the Stamos offers a high degree of freedom of movement. This allows you to work continuously even in a larger working radius without problems.
In order to achieve the maximum working progress for each task, the Stamos offers two different working modes. In 2-stroke mode, the torch will run for as long as the power switch is pressed. In 4-stroke mode, a single tap is sufficient to activate the burner and another tap to switch it off. This mode provides countless advantages for continuous operation. The handle position on the torch can be varied during work to reduce fatigue and physical strain.
To prevent damage to the torch or deformation of the workpiece and oxidation reactions after the cut, the air cooling continues to run afterward. The post-flow interval can be selected between 5 and 60 s in several steps. The power unit is protected against damage by fan cooling and overheating protection.
Problems with the operating temperature as well as other malfunctions are indicated by an LED on the control unit. The LED display for the cutting current and the cutting current controller are also located in this clearly visible space on the front of the unit. With a product weight of 33.9 kilograms, the plasma cutter has sufficient mass to maintain safe footing even in a rugged working environment.
Accessories
Ratings & reviews
Ratings & reviews
5
Based on 12 reviews
Sort by :
Professionally made plasma cutter with a large power reserve. 3 x 400V power supply is a big advantage for those who have three-phase power supply available in their workshops. When plasma cutting thicker elements, the power load is distributed over three phases and we do not overload the electrical installation as it happens with devices powered from one phase 230V. I recommend the device for equipping a workshop as a stationary one. You can power a CNC plotter from this device and it will work well, because the parameters of the device allow for long continuous operation at a current of up to 80A. All spare and consumable elements are available - standard and not expensive. For this price, the device exceeded my expectations.
Show original review
The product is excellent, cuts 30mm without a problem, fast delivery.
Show original review
No comment provided.
Show original review
The 30mm works very well, they fell beautifully. The price-performance ratio is very good. I recommend it 😇
Show original review
Very good
Show original review
I am completely satisfied with the product. The delivery was fast and accurate, and the package was undamaged.
Show original review
Works better than expected
Show original review
Maximum satisfaction, I can only recommend. Thanks a lot for everything
Show original review
It is easy to use and cuts nicely and neatly
Show original review
We tested the plasma cutter directly and it was convincing across the board. Delivery worked great.
Show original review
Frequently asked questions
What's the maximum thickness of material the plasma cutter can cut through?
The maximum thickness is 34 mm.
Is the plasma cutter easy to transport?
Despite its compact size, the unit weighs 33.9 kg, so we recommend using a welding cart for transport. You can also find a selection of welding trolleys at expondo.
How does the device inform me when it's threatening to overheat?
A diode lights up as soon as the maximum duty cycle is exceeded and the device heats up too much as a result. The light will also warn you if the plasma cutter generates too much heat due to malfunction. In both cases, the operation should be interrupted.
THE EXPERTS CHOICE
16 YEARS OF EXPERIENCE...
of powering professionals
3 MILLION...
happy and satisfied professional customers